Testimonials:

1, the machine placed a smooth, connected to the power , drive power and welding power, please separate the connection, welding 20A circuit breaker, drive 10A circuit breaker.

2, connected to the gas source, the foot switch is pressed cylinder control components, step down under pressure, once again under the open.

3, the factory has been fully commissioned for the factory, the user should not change its parameters and electric circuit within the box, only need to change the welding length can meet the welding requirements.

4, the welding wire into: the [automatic / manual] button to the manual state, the left hand holding the wire into the pressure wheel, right hand press [wire down], wire through the pressure wheel, through the guide wheel, Guide tube, wire head exposed tube about 7-8mm.

5, the parameters of the adjustment range:

A, move to welding distance: Please try to keep the original parameters.

B, before welding wire down distance: 12-13mm between.

C, welding length: according to the actual welding length appropriate addition and subtraction.

D, when finished welding wire speed: 4800-5000 between the adjustment.

E, when finished welding wire length: 12-13mm between.

F, welding wire moving speed: 3200 or so, according to the diameter of the wire diameter for the corresponding adjustments.

G, welding the workpiece is completed according to the size of the end of the gap to determine the number of welding.

①、Machine installation:

As this machine is big, the host should be horizontal, and the stainlesssteel plate should be horizontal at the same height.

②、Trial operation：

The power supply for three-phase 380V,using frequency conversion stepless speed regulation. Connect air source,operate the top wheel and roll wheel action button A. B. (A Control the roll, B control the top wheel),check if it is flexible.

③、the prepare before starting.

⑴, confirm the metal ring, steel strip, graphite are in line with the requirements of the winding pad (including specifications, material, quality).

⑵, confirm the core crown, conformity to product requirements.

④、Operation steps:

⑴、put the ring into the core,between the top wheel.operation the manual vavle A,the roll wheel pressing. Then operating manual vavle B,the top wheel push the metal ring.operating the foot button,making the metal ring turing up. Make sure the metal ring is flat and smooth,put the guide wheel at the inner ring then tighten it.

⑵、Pull out the forming steel strip,welding the strip at the metal ring,the metal ring and the strip should not have a serious deviation. The strip should be welded three or four circles, then welded firmly.

⑶、pull out the graphite tape,into wound. Wound to the require size.

⑷、cut the graphite tape,then wound the forming steel strip,to the required size. Cut the strip,then weld firmly.operation finished.

CIXI HEROOS SEALING MATERIALS CO.,LTD

Metal Tape Cutting Machine simple Operating Instructions

Cixi Heroos Sealing Materials Co.,Ltd.

the installation:

Carefully open the wooden box packaging machine, the machine and place smoothly moved to the installation location.

the test run:

Power (according to the labeling requirements into line machine wiring), check the blade meets the processing requirements, operating inverted switch to start the machine, observe the rotational direction of the blades is correct, if not correct, you need to change the rotation direction of commutation.

before the start of the preparation:

1, the blade is sharp.

2, blade width to meet the requirements.

3, the cutting fluid prepared, spare brushes.

4, raw materials meet the requirements.

5, the discharge end of the feed tray to put in front of 5-6 meters.

steps:

1. Open the packaging material and pull one end of the outer end of the strip, via guide wheels underneath, so that an S-shaped raw material import slitting head.

2, adjust the front guide carriage, complete wire scrap regulation

3, stop the machine when the points of separation of about 2.5 meters, will hang each strip into the adjustment dial rewinding shaft.

4, again start slitting machine (as the case to raise the blade cutting fluid).

5. Receipt steel plate should not be too close to the outer circumference, stop the machine cut steel, steel plate removed one by one, to complete the operation.

                                                                                                              Cixi Heroos Sealing Materials Co.,Ltd.

Automatic Ring Bending Machine with metal spiral wound gasket manufacturing equipment matching a mechanical device, which is the production and processing of metal spiral wound gasket strengthen a non-standard equipment of the ring. read more